
Sioux Falls and nearby towns
Generator Installation Sioux Falls SD
Standby units, transfer switches, and inlets. No backfeed setups.
Generator installation in Sioux Falls covers a home backup generator (a standby unit), a transfer switch, or an inlet for a portable generator. The panel has to accept the switch, and the generator must not backfeed the utility lines. A portable inlet is a different job from a standby set. Call (605) 250-4838.
Updated
What’s included
The safe part is the transfer switch, not just setting a generator on a pad. We will not hook up a double-ended cord.
Manual transfer switches and interlock kits that the panel can accept. We check your panel before we pick a kit.
Inlets and cords for a portable generator you already own. Send us the model or a photo of the label.
Standby units with an automatic transfer switch when the site fits. The pad and the fuel line are part of that job.
A circuit list so the generator is not asked to run the whole house unless it is sized for that. We write down what it will run before we connect the switch.
Coordination with the utility when a standby set needs their approval. We call the power company only when they have to sign off.
A clear refusal of any double-ended cord or backfeed trick. Backfeeding can put power on the utility lines.
Signs you need a home backup generator
Think about a generator before storm season if an outage costs you heat, a sump, or a medical device. If you already own one, have the model number handy.
You run a generator with an extension cord through a door. An inlet is the right way to bring that power inside.
A sump, freezer, or oxygen machine has to stay on. Tell us those first so we put them on the generator.
The panel has no inlet and no transfer switch. Without one, the generator stays off your house wiring.
A previous outage lasted long enough to spoil food or flood a basement. We start the list with what you lost.
You bought a generator and it is still in the box. The label tells us what your panel can take.
What affects emergency generator installation cost
What you pay depends on how hard the wires are to reach, the parts, and whether your city wants a permit. We do not list one price here. Typical published national ranges are shown below as a rough guide only.
- 1
A portable inlet is a smaller job than a standby set with a concrete pad, gas piping, and an automatic switch. Fuel type, distance from the panel, and the circuits you choose all change the price.
- 2
Bring the model number or a photo of the nameplate.
24/7 emergency service
Do not backfeed the house during an outage. That can energize the utility lines. Call for a proper inlet instead of improvising in the storm.
Calls answered 24 hours a day, 7 days a week, including emergency service.
How much does a Generac whole house generator cost installed?
Published national figures put whole house generator installation at about $1,500 to $8,800, with an average near $5,200. The generator itself is priced mostly by size, and Generac units start around $6,000. Installation, the pad, the transfer switch, the gas or propane connection, and the permit add to the unit price.
| Generator size | Typical published generator cost | What it usually runs |
|---|---|---|
| Generator size14 to 18 kW | Typical published generator cost$4,000 to $5,500 | What it usually runsessentials plus central air and a water heater |
| Generator size20 to 24 kW | Typical published generator cost$5,000 to $6,500 | What it usually runsmost of the house, including larger appliances |
| Generator size26 to 32 kW | Typical published generator cost$6,500 to $15,000 | What it usually runswhole house with larger HVAC systems |
Typical published national ranges, not a quote. Rough estimate only. Your final price comes after an electrician sees the job.
Source: Angi, whole house generator cost, updated Sep 1, 2026
Natural gas or propane
In town, most standby units run on natural gas. On acreages around Hartford, Canton, and Dell Rapids without a gas line, propane is the usual fuel. Fuel choice changes the connection work.
Why winter matters here
Blizzards and ice storms are when backup power matters most. Plan the install before the ground freezes so the pad and gas line go in easily.
Permit and utility
The question [Do standby generators need the utility involved?](#faq-do-standby-generators-need-the-utility-involved) stays and covers this.
Generator transfer switch installation
A transfer switch lets a generator power your home without backfeeding the utility lines. Published national figures put transfer switch installation at about $1,200 to $1,600, with an average near $1,450. Manual switches run about $400 to $1,300 installed and automatic switches about $600 to $2,500.
| Type | Typical published installed range | Best for |
|---|---|---|
| TypeManual transfer switch | Typical published installed range$400 to $1,300 | Best forportable generators, you flip it on |
| TypeAutomatic transfer switch | Typical published installed range$600 to $2,500 | Best forstandby generators, switches on its own |
| TypePermit (varies by city) | Typical published installed range$50 to $350 |
Typical published national ranges, not a quote. Rough estimate only. Your final price comes after an electrician sees the job.
Source: Angi, generator transfer switch cost, updated Oct 16, 2026
Transfer switch or interlock kit?
See [Interlock kit or transfer switch: which do I need, and does it need a permit?](#faq-interlock-kit-or-transfer-switch-which-do-i-need-and-does-it-need-a-permit) No interlock price is published here.
Never use a dryer outlet
See [Can I plug a generator into a dryer outlet?](#faq-can-i-plug-a-generator-into-a-dryer-outlet)
How the visit goes
Tell us what is wrong, and we stick to that. If we find a second problem, we tell you before we keep going.
- 1
You call
Send the model or a photo of the nameplate when you already own the unit. On site the panel is checked for a place to land a transfer switch or an interlock, and the pad or inlet spot is marked.
- 2
On site
The notes list the circuits that will be on the generator and the circuits that stay off. A double-ended cord is not offered.
- 3
The work
After the switch is in, those circuits are tested with the utility separated by the transfer equipment. The utility is contacted only when that setup needs their approval.
Towns served
This work is available in Sioux Falls, Brandon, Harrisburg, Tea, Hartford, Dell Rapids, Canton, and Lennox. See the service area.
Related services
These are the jobs that often come up next. Open a card to see what that visit covers.

Panel upgrades
Replace a full, warm, or outdated panel, including an old fuse box. We size the new panel for your service and for what you want to add.
Learn more →
Emergency electrician
Sparking, a burning smell, or power out in part of the building. Call 911 if there is smoke or fire.
Learn more →
Surge protection
Whole-house surge protection installed at the panel. A plug-in strip only covers what you plug into it.
Learn more →
Questions about this work
Can I plug a generator into a dryer outlet?
No. A dryer outlet is not a transfer switch. Backfeeding can send power onto the utility lines and injure a line worker. Use an inlet and a transfer method.
Will a portable generator run the whole house?
Usually no. The circuits that fit the unit you have are the ones on the generator, such as a furnace fan, a fridge, and a few lights.
Do standby generators need the utility involved?
Often yes, because the automatic switch sits between the meter and the panel. The visit notes when that approval is part of the job.
Where should the generator sit?
Away from windows and the intake of a furnace, on a pad the manufacturer allows. The visit marks a spot.
Interlock kit or transfer switch: which do I need, and does it need a permit?
An interlock kit lets a portable generator power selected circuits through your panel. A transfer switch (manual or automatic) is for a standby generator or a fixed setup. Both need a licensed electrician and typically a permit so utility power and generator power cannot backfeed each other.
How much does a Generac whole house generator cost to install?
Published national figures put whole house generator installation at about $1,500 to $8,800, with an average near $5,200, and Generac units starting around $6,000. Size, fuel, the pad, and the transfer switch decide where your job lands.
What size generator do I need for my house?
Published sizing guides suggest about 10 to 14 kW for a 2,000 square foot home and 16 to 20 kW or more for 3,000 square feet, depending on what you want to run. Try our generator size calculator for a quick start.
How much does a generator transfer switch cost?
Published national figures put transfer switch installation at about $1,200 to $1,600 on average, with manual switches about $400 to $1,300 and automatic switches about $600 to $2,500.
Do I need a transfer switch for a portable generator?
You need a safe way to connect it, either a transfer switch or an interlock with an inlet. Plugging a generator into an outlet can backfeed the utility lines and injure a line worker.

Need help with a generator installation?
Calls answered 24 hours a day, 7 days a week, including emergency service. Tell us if it is your house or your business.